Preet 955 Challenger full specifications

Preet 955 Challenger tractor has 3 cylinder naturally aspirated liquid cooled engine with 3066 cc displacement which can produce about 50 hp at 2200 engine rated RPM. Tractor can produce maximum 190 Nm torque. Tractor has 1500 kg weight lifting capacity with 3 point linkage system. Here are some more specifications of tractor:


Engine

Specifications Data
1. Engine MakeNo data available
2. Engine Type
  • 3 Cylinder
  • 4 Stroke
  • Naturally aspirated
  • Liquid Cooled
  • Direct Injection
  • Diesel Engine
3. Max Torque190 +- 5% Nm
4. HP50 hp category
5. Bore*Stroke (MM)105*118 mm
6. Displacement3066 CC
7. Engine rated RPM2200
8. PumpInline Bosch
9. Max engine RPM in tachometer3000
10. SFCNo data available
11. Idle RPM650 +- 50
12. Max. RPM at no load2350 +-100
13. Firing order1-3-2
14. Compression ratio18.5+-1:1
15. Fuel injections timing11°+-1° BTDC
16. Valve clearance0.30 mm for inlet in cold & hot conditions
0.40 mm for outlet in cold & hot conditions

Transmission

Specifications Data
1. Clutch type & sizeSingle with 280 mm diameter (standard)
Dual with 280 mm dia (optional)
2. Transmission 8F+2R
3. Clutch paddle free play20-25 mm
4. Transmission typeSliding mesh

Gear speed of tractor

GearSpeed
L12.69
L23.32
L35.49
L48.67
H110.60
H213.07
H321.63
H434.15
L-R3.77
H-R14.84

Brakes

Specifications Data
1. TypeMultidisc mechanical brakes (standard)
Wet brakes (optional)
2. Minimum turning diameter with brakesNo data available
3. Minimum turning diameter without brakes3.97 meter
4. Brake paddle free play35 to 40 mm

Steering

Specifications Data
1. MechanicalAvailable (standard)
2. PowerAvailable (optional)
3. Oil capacity (power steering)2 liters
4. Oil capacity (mechanical steering)0.5 liter

PTO

SpecificationsData
1. PTO HP @ Rated RPMNo data available
2. PTO speeds-Standard540 PTO CR (No data available about engine RPM)
3. PTO speeds – EconomyNot available
4. PTO speeds – ReverseNot available
5. PTO speeds – Ground speedNot available

Hydraulics

Specifications Data
1. TypeLive Auto depth and draft control
2. Weight lifting capacity 1500 kg

Tyres

Tyre size
Air pressure in
In fieldIn haulage
7.50*16
28 psi
14.9*28
16.9*28
16 psi18 psi

Overall dimensions

Specifications Data
1. Wheel base2150 mm
2. Overall length3700 mm
3. Overall width1800 mm
4. Overall height2235 mm
5. MIN. Ground clearance415 mm
6. Weight of tractor (without ballast)No data available

Other

Specifications Data
1. Battery12 V, 88 Ah
2. Alternator35/42 Amps.
3. Fuel tank capacity67 Liters
Preet 955

Oil & Lubrication

PartsAmountType
Engine oil8 liters20W40
Air cleaner1 liter20W40
Transmission/Hydraulics55 litersTRACTELF (for wet brakes)
EP-80 (for dry brakes)
Power steering2 liters20W40
Mechanical0.5 literEP-140
Coolant9.2 litersNo data available
GreaseAs requiredNo data available

Unfortunately there is no data available for implement selection.

To know about troubleshooting please visit Preet 6049 tractor page.

Here is some information about periodic maintenance of tractor:

Periodic Maintenance chart for Preet 6049 tractor

JobsHours every
105070100
Cleaning of whole tractor
Check & tight nuts
Check water level in radiator
Check air cleaner element
Lubrication of all greasing points
Check leakage of engine oil
Check air pressure in tyres
Clean suction strainer
Change air cleaner oil if applicable
Check battery electrolyte level & clean terminals
Clean feed pump
Drain out water fuel filters
Check fan belt condition
Check free play in clutch & brake paddle
If dry air cleaner element then clean element
Check oil level in engine & transmission
Lubricate front axle center pins
Lubricate king pins & lift rods
Clean suction strainer
JobsHours every
2505007501000
Flush crankcase
Change engine oil & oil filter
Clean radiator fins
Change transmission oil
Clean fuel tank
Change primary fuel filters
Interchange front tyres to avoid improper wear
Check free play in tapper bearing of front wheel
Flush cooling system with clean water
Change paper element of air cleaner
Change strainer
Change secondary fuel filter
Clean front wheel hub and re lubricate
Remove carbon from cylinder and cylinder head
Grind valve if necessary
Check play in water pump bearing
Servicing of alternator, starter and battery
Adjustment of valve clearance
Servicing of nozzles

More models:

Leave a Comment


The reCAPTCHA verification period has expired. Please reload the page.