John Deere 5042D tractor full specifications: tractor has 3 cylinder naturally aspirated liquid cooled engine with 2939 CC displacement which can produce about 44 hp at 2100 engine rated RPM. Tractor can produce 170 Nm torque at 1200 engine RPM. Tractor has 1400 weight lifting capacity and 1810 kg its own while 60 fuel tank capacity. Here are more specifications of tractor:
Price
Price of John Deere 5042D tractor starts from Rs 7,15,000 and goes up to Rs 7,70,000 which is due to different different area dealerships.
Engine
| Specifications | Data |
|---|---|
| 1. Engine Make | John Deere |
| 2. Engine Type |
|
| 3. Max Torque | 170 Nm torque at 1200 rpm |
| 4. HP | 44 hp |
| 5. Bore*Stroke (MM) | 106.5*110 mm |
| 6. Displacement | 2939.71 CC |
| 7. Engine rated RPM | 2100 |
| 8. Pump | Inline Bosch |
| 9. Max engine RPM in tachometer | 3000 |
| 10. SFC | No data available |
| 11. Idle RPM | 850 +- 50 |
| 12. Max. idle RPM | 2300 +-50 |
| 13. Compression ratio | 18.5:1 |
| 14. Fuel injection timing | 12.5° BTDC |
Transmission
| Specifications | Data |
|---|---|
| 1. Clutch type & size | Single & dual (size not available) |
| 2. Transmission | Collar shift with 8F + 4R |
| 3. Clutch paddle free play | 20-25 mm |
Gear speed with 13.6*28 tyres
| Gears | Speed in kmph |
|---|---|
| A1 | 2.84 |
| A2 | 4.18 |
| A3 | 6.51 |
| A4 | 10.29 |
| B1 | 8.59 |
| B2 | 12.62 |
| B3 | 19.68 |
| B4 | 31.07 |
| R1 | 3.74 |
| R2 | 5.49 |
| R3 | 8.56 |
| R4 | 13.52 |
Brakes
| Specifications | Data |
|---|---|
| 1. Type | Mechanical Wet disc Brakes |
| 2. Minimum turning radius with brakes | 2.9 meters |
| 3. Minimum turning radius without brakes | 3.2 meters |
| 4. Brake paddle free play | 20 to 30 mm |
Steering
| Specifications | Data |
|---|---|
| 1. Mechanical | Not available |
| 2. Power | Available (standard) |
| 3. Oil capacity (power steering) | There is no separate oil tank for power steering oil. |
PTO
| Specifications | Data |
|---|---|
| 1. PTO HP @ Rated RPM | 35.5 hp |
| 2. PTO speeds-Standard | Available (540 PTO RPM at 2050 engine RPM) |
| 3. PTO speeds – Economy | 540 PTO RPM at 1600 engine RPM |
| 4. PTO speeds – Reverse | Available (228 at 1200 ERPM) |
| 5. PTO speeds – Ground speed | Not available |
Hydraulics
| Specifications | Data |
|---|---|
| 1. Type | Live Auto depth and draft control |
| 2. Lift capacity | 1400 kg with three point linkage system. |
Tyre pressure according to conditions
| Tyre | Without heavy load | With ballast or heavy equipment |
|---|---|---|
| 6.00*16 | 23 psi | 40 psi |
| 13.6*28 | 13 psi (in field also) | 18 psi (on road also) |
Overall dimensions
| Specifications | Data |
|---|---|
| 1. Wheel base | 1950 mm |
| 2. Overall length | 3335 mm |
| 3. Overall width | 1775 mm |
| 4. Overall height (up to exhaust pipe) | 2210 mm |
| 5. MIN. Ground clearance | 415 mm |
| 6. Weight of tractor | 1810 kg |
Others
| Specifications | Data |
|---|---|
| 1. Battery | 12 V, 88 Ah |
| 2. Alternator | 42 Amps. |
| 3. Fuel tank capacity | 60 Litres |
NOTE: All these specifications are applicable for John Deere 5042D and John Deere 5042D V3 tractors.
Here are details about oil amount and type which is helpful before operating periodic maintenance service:
Oil & Lubrications
| Part | Amount | Type |
|---|---|---|
| Engine | 6.5 litres | SAE 15W-40 |
| Transmission & Hydraulics | 30 litres for grease axle 32 litres for oil axle | BIO-HY-GARD |
| Coolant | 9.8 litres | John Deere COOL-GARD II |
| Grease | As required | John Deere GREASE-GARD |
Instrument cluster
- Hour meter.
- High beam indicator.
- Air cleaner clog indicator.
- System charging indicator.
- Engine oil pressure gauge.
- Turn indicator lights.
- Engine coolant temperature indicator.
- Tachometer with 3000 max RPM.
- Fuel gauge.
- Reverse PTO indicator.
To get maximum performance and low fuel consumption from tractor it is very select correct implement for tractor, to better understand about it here is a table for implement selection:
Implement selection
| Implement | Type |
|---|---|
| MB plough | 2 bottom |
| Reversible MB plough | 1 bottom |
| Disc plough | 2 disc |
| Offset Disc harrow | 12 and 14 discs |
| Trailed disc harrow | 12 to 14 discs |
| Cultivator (rigid spring) | 7 to 11 tines |
| Rotavator | 1.25 to 1.50 metre |
Type & size of implement and gear selections will change with soil conditions and for that you have to visit nearest service center.
There are some jobs which should be performed according to their time to increase performance and life of tractor.
Things to inspect daily or after every 10 hours:
- Check engine oil level.
- Check coolant level daily.
- Drain out water from fuel filters.
- Grease all lubrication points.
- Check air pressure in tyres.
Things to inspect after every 50 hours:
- Check level of transmission-hydraulic oil level.
- Check MFWD axle oil level.
- Clean battery & there should be no corrosion on the terminals.
- Grease front axle pivot pins.
- Grease steering spindles.
- Lubricate clutch & brake paddles.
- Check free play in clutch, brake paddles and fan belt tension.
Periodic Maintenance Chart
| Jobs | ||||
|---|---|---|---|---|
| 250 | 500 | 600 | 1250 | |
| Change engine oil & oil filters | ✓ | |||
| Service of air cleaner | ✓ | |||
| Change fuel filters | ✓ | |||
| Check condition of fan belt | ✓ | |||
| Lubrication of 3 points hitch | ✓ | |||
| Check neutral start switch system | ✓ | |||
| Change transmission-hydraulic filter | ✓ | |||
| Lubrication of rockshaft control support lever | ✓ | |||
| Change oil MFWD axle | ✓ | |||
| Clean engine crankcase tube | ✓ | |||
| Check & tight hoses and hoses clips | ✓ | |||
| Lubricate rear axle bearings | ✓ | |||
| Check engine idle speed | ✓ | |||
| Check front axle pivot pins | ✓ | |||
| Tight front turning bolts | ✓ | |||
| Check water separator tap | ✓ | |||
| Change trasmission oil & oil fiter | ✓ | |||
| Clean transmission, hydraulic pickup screen | ✓ | |||
| Change air cleaner element | ||||
| Flushing of coolant | ||||
Time period for cleaning of air cleaner element may be early because of environmental conditions and to better understand about it you have to visit nearest authorized service center.
After 2 years jobs:
- Flush cooling system at least once.
- Replace water separator.
- Check and adjust throttle friction.
There are some job which will be performed according to need:
- Changing of alternator/fan belt.
- Servicing/replacement of battery.
- Cleaning of grills and fins of radiator.
- Bleeding of fuel system.
- Adjustment of headlights focus.
- Changing/retreading of tyres.
- Tyre pressure adjustment.
Weights and water ballasting
On rear side you can mount cast iron weight plate of 48 kg which should be of company recommended design but before mounting weights there is an important thing i.e. torque specs for weights and hub bolts which is given below:
| Parts | Torque amount |
|---|---|
| Front disc to hub | 210 Nm |
| Rear disc with rim | 245 Nm |
| Rear disc with hub bolts | 550 Nm |
| Bolts for ROPS adjusment | 420 +- 10 Nm |
| Rear weight with disc | 230 Nm |
More models:
John Deere 5050 D full specification & Gear speeds