2025 John Deere 5050 D tractor price & full specification

John Deere 5050 D full specification: tractor has 3 cylinder naturally aspirated liquid cooled engine with 2939 CC displacement which can produce 50 hp 2100 engine rated RPM. Tractor has Dual clutch with 8 forwards and 4 reverse transmission with collar shift technology. Tractor has standard 1400 kg weight lifting capacity and 60 liters fuel tank capacity. Tractor can generate 192 Nm torque at 1200 ERPM. Here are full specifications of tractor:

Table of Contents

Price

Price of John Deere 5050 D tractor starts from Rs 8,35,000 and goes up to Rs 9,20,000 which is due to different area dealerships.

Engine

Specifications	Data
1. Engine Make	John Deere
2. Engine Type	3 Cylinder 4 Stroke Naturally aspirated Liquid Cooled Direct Injection Diesel Engine
3. Max Torque	192 Nm torque at 1200 rpm
4. HP	50 hp
5. Bore*Stroke (MM)	106.5*110 mm
6. Displacement	2939.71 CC
7. Engine rated RPM	2100
8. Pump	Inline Bosch
9. Max engine RPM in tachometer	3000
10. SFC	No data available
11. Idle RPM	850 +- 50
12. Max. idle RPM	2300 +-50
13. Compression ratio	18.5:1
14. Fuel injection timing	10° BTDC

Transmission

Specifications	Data
1. Clutch type & size	Dual (size not available)
2. Transmission	Collar shift with 8F + 4R
3. Clutch paddle free play	20-25 mm

Gear speed chart of tractor with 12.4*28 rear tires:

Gears	With Low speed planetry system	With high speed planetry system
Gears	speed in kmph	speed in kmph
A1	2.74	3.13
A2	4.02	4.6
A3	6.27	7.18
A4	9.9	11.32
B1	8.26	9.44
B2	12.15	13.88
B3	18.94	21.69
B4	29.91	34.18
R1	3.6	4.1
R2	5.29	6.03
R3	8.24	9.42
R4	13.01	14.84

Gear speed chart of tractor with 13.6*28 rear tires:

Gears	With Low speed planetry system	With high speed planetry system
Gears	speed in kmph	speed in kmph
A1	2.83	3.23
A2	4.16	4.75
A3	6.5	7.42
A4	10.24	11.70
B1	8.54	9.76
B2	12.56	14.36
B3	19.62	22.42
B4	30.92	35.34
R1	3.71	4.24
R2	5.45	6.23
R3	8.52	9.74
R4	13.43	15.34

Brakes

Specifications	Data
1. Type	Mechanical Wet disc Brakes
2. Minimum turning radius with brakes	3 meters (for 2WD) 3 meters (for 4 WD)
3. Minimum turning radius without brakes	3.2 meters (for 2 WD) 3.2 meters (for 4 WD)
4. Brake paddle free play	20 to 30 mm

Steering

Specifications	Data
1. Mechanical	Not available
2. Power	Available (standard)
3. Oil capacity (power steering)	There is no separate oil tank for power steering oil.

PTO

Specifications	Data
1. PTO HP @ Rated RPM	41.5 hp
2. PTO speeds-Standard	Available (540 PTO RPM at 2050 engine RPM)
3. PTO speeds – Economy	540 PTO RPM at 1600 engine RPM
4. PTO speeds – Reverse	Available (228 at 1200 ERPM)
5. PTO speeds – Ground speed	Not available

Hydraulics

Specifications	Data
1. Type	Live Auto depth and draft control
2. Lift capacity	1400 kg with three point linkage system.

Tyres & pressure according to conditions

Tyre	Pressure without heavy load	Pressure with ballast or heavy equipment
For front tyre
6.0016 7.5016	23 psi 20 psi	40 psi 40 psi
For rear tyre
12.4*28	12 psi (in field also)	20 psi (on road also)
13.6*28	13 psi (in field also)	18 psi (on road also)

Overall dimensions

Measurements	For 2WD	For 4WD
1. Wheel base	1950 mm	1950 mm
2. Overall length	3370 mm	3350 mm
3. Overall width	1805 mm	1775 mm
4. Height up to exhaust pipe	2220 mm	2220 mm
5. Min. ground clearance	440 mm	365 mm
6. Total weight	1830 kg	1975 kg

Others

Specifications	Data
1. Battery	12 V, 88 Ah
2. Alternator	42 Amps.
3. Fuel tank capacity	60 Litres

John Deere 5050 D

Here are the details about lubrication oil type for the tractor:

Oil & Lubrications

Part	Amount	Type
Engine	8.5 litres	SAE 15W-40
Transmission & Hydraulics	30 litres for grease axle 32 litres for oil axle	BIO-HY-GARD
Coolant	9.8 litres	John Deere COOL-GARD II
Grease	As required	John Deere GREASE-GARD

Here is the details about instrument cluster of tractor:

Tachometer with 3000 max engine RPM.
Fuel gauge.
Engine temperature gauge.
Air cleaner clog indicator.
High beam indicator.
Digital hour meter.
Engine oil pressure gauge.
System charging indicator.
Turn indicator light indicator.
Reverse PTO engagement indicator.

Implement selection

Selection of perfect implement is of the most important thing which is responsible for the overall performance of tractor and better understand about here is a table chart for implement selection:

Implement	Type
MB plough	2 bottom
Reversible MB plough	1 & 2 bottom
Disc plough	2 & 3 disc
Offset Disc harrow	12, 14 and 16 discs
Trailed disc harrow	12, 14, 16 and 18 discs
Cultivator	7, 9, 11 and 13 tines
Rotavator	1.25, 1.50 and 1.75 meters

NOTE: Type & size of implement may change according to soil condition, especially in case of rotavator.

Things to check daily or after every 10 hours:

Check and top up engine oil level.
Check transmission & hydraulic oil level and top up if level is below recommended mark.
Check & top up coolant level.
Check & adjust tyre pressure according ballast and other conditions.
Lubricate all greasing points.

Jobs to be done after every 50 hours:

Check front 4WD axle oil if provided.
Grease front axle pivot pins.
Check battery terminals and there should be no corrosion on battery terminals.
Grease steering spindles.
Lubricate clutch & brake paddles pins.
Check & adjust free play in clutch, brake paddle and tension in fan belt.

Here is the full details about tractor’s periodic maintenance chart which is very helpful during tractor’s service schedule:

Periodic Maintenance Chart

Jobs	Hours
Jobs	250	500	600	1250
Change engine oil & oil filters	✓
Service of air cleaner	✓
Change fuel filters	✓
Check condition of fan belt	✓
Lubrication of 3 points hitch	✓
Check neutral start switch system	✓
Change transmission-hydraulic filter		✓
Lubrication of rockshaft control support lever		✓
Change oil MFWD axle			✓
Clean engine crankcase tube			✓
Check & tight hoses and hoses clips			✓
Lubricate rear axle bearings			✓
Check engine idle speed			✓
Check front axle pivot pins			✓
Tight front turning bolts			✓
Check water separator tap			✓
Change trasmission oil & oil fiter				✓
Clean transmission, hydraulic pickup screen				✓
Change air cleaner element	Once in a year
Flushing of coolant	After every 2 years

There are some parts which may be replaced before recommended time period because of environmental conditions such as air cleaner element because of dusty environmental conditions and fan belt.

Apart from this service maintenance chart there are some things which will be done according to need:

Replacement of battery (life of battery depends on environmental conditions and style of starting tractor first time in early morning).
Replacement of fan belt.
Cleaning of radiator fins.
Adjustment of front headlight focus.
Cleaning of air cleaner element.
Changing/retreading of tyres.

Troubleshooting

Here are some basic & advance problems which may happen with tractor and their possible reasons are also mentioned below these:

Engine not starting or starting with problem:
- Wrong starting procedure.
- Low fuel level in fuel tank.
- Air trapped in fuel lines.
- Wrong fuel selection.
- Blockage in fuel filtres.
- Fuel shut off valve is off.
- Low temperature of coolant.
- Fault in fuel injection pump.
- Engine overheating.
Low engine temperature:
- Fault in thermostat.
- Fault in temperature gauge.
Low power output:
- Engine overloading.
- Low idle RPM.
- Air cleaner clogged.
- Wrong fuel selection.
- Blockage in fuel filters.
- Low engine temperature.
- Wrong valve clearance setting.
- Fault in fuel injectors.
- Fault in fuel injection pump.
- Leakage in exhaust manifold gasket.
- Blockage in fuel line.
- Wrong implement selection.
- Blockage in fuel return line.
- Extra ballasting.
Low engine oil pressure:
- Low level of engine oil.
- Selection of wrong grade for engine oil.
- Leakage of engine oil.
Engine oil consumption:
- Selection of light engine oil.
- Leakage of engine oil.
- Blockage in crankcase tube.
White smoke problem:
- Cold starting.
- Low engine temperature.
- Selection of wrong fuel type.
- Fault in thermostat.
- Fault in injection nozzles.
- Damage in cylinder walls.
- Wrong valve clearance setting.
Black or grey smoke problem:
- Selection of wrong fuel type.
- Blockage of air cleaner element.
- Engine overloading.
- Fault in injection nozzles.
- Wear & tear of cylinder walls and piston.
- Wrong valve clearance setting.
Engine overheating problem:
- Radiator fins are clogged.
- Engine overloading.
- Low level of engine oil.
- Fault in radiator cap.
- Low level of coolant.
- Loose fan belt.
- Fault in thermostat.
- Selection of wrong of grade of engine oil.
- There is need to flush cooling system.