New Holland 3630 TX Super plus specifications & gear speeds

New Holland 3630 TX Super Plus tractor has 3 cylinder naturally aspirated liquid cooled FPT engine with 2931 cc displacement which can produce 49.53 hp at 2100 engine rated RPM. Tractor has double clutch with independent PTO clutch lever, ground PTO & reverse PTO. Tractor has 1700 kg lift capacity which can extended to 2000 kg by using Asist Ram. Tractor has fully constant mesh transmission with 3 types different options:

• 8F+2R.
• 12F+3R Creeper.
• 12F+3R UG.

Here are full specifications of tractor:

Price for New Holland 3630 TX Super plus tractor is Rs 8.50 to 9.25 lakhs in 2023.

Engine

Transmission

Gear speeds for 8F + 2R transmission on engine rated RPM:

Speeds for 12F + 3R creeper transmission

There is difference in 12F + 3R transmission speeds in 2 wheel drive and 4 wheel drive variants, here are both.

Gear speeds for 12F + 3R transmission in 2 wheel drive variant:

Gear speeds for 12F + 3R transmission in 4 wheel drive variant:

Brakes

Steering

PTO

PTO ground speeds for 8F+2R and 12F + 3R creeper transmission:

Hydraulics

Tires

Overall Dimensions

In 4 wheel drive front tire size is “9.5*24” and rear tire size is “16.9*28” and according these tires dimensions in 4 wheel drive variant are measured.

NOTE: The above dimensions are only applicable with 16.9*28 rear tyre size and 6.0*16 front tyre size and tractor’s weight is without ballast.

Others

Oil & Lubrications

The first 50 hours service:

• Check and adjust fan belt tension.
• Change engine oil and oil filter.
• Change fuel strainer.
• Change hydraulic oil filter.
• Change primary fuel filter.
• Check 4 WD axle hub and differential oil level.
• Check all hose connections of air filter and cooling system and tighten if these are loose.
• Tight front and rear hub bolts with specific torque and also tight rear weight bolts.

Torque amount for wheel bolts and weight plates on wheels:

Torque amount for bolts

After first 50 hours of use:

• Change engine oil fluid.
• Change engine oil filter.
• Replace fuel filters.
• Change hydraulic oil filter.
• Change fuel strainer.

After every 10 hours of use:

• Check engine oil level.
• Check radiator coolant level.
• Clean air pre cleaner.
• Clean air cleaner bowl.
• Drain water from fuel filters.

After every 50 hours of use:

• Check and adjust clutch and brake paddle free play.
• Clean air cleaner gauge filter.
• Check parking brake lock.
• Check and adjust tire pressure.
• Check hub bolts.
• Check fan belt tension.
• Lubricate greasing points.
• Check front axle differential and differential hub oil level.
• Check sources of leakages.

After first 300 hours of use:

• Change front 4 wheel drive axle differential oil.
• Change front 4 wheel drive hub oil.

After every 300 hours of use:

• Change engine oil and engine oil filters.
• Change fuel feed pump and replace fuel filters.
• Check hydrostatic steering oil level.
• Replace hydraulic oil filter.
• Check and top up transmission oil level.
• Lubricate front axle swivel bearings.
• Change fuel strainer.
• Check drive shaft sleeve for 4 wheel drive connections.

After every 600 hours of use:

• Check and adjust valve clearance.
• Change fuel filters.
• Clean transmission oil vapor breather.
• Clean, adjust and re-grease front wheel bearings.
• Service of fuel injectors.
• Front wheel toe-in adjustment.

After every 1200 hours of use:

• Change transmission and hydraulic oil.
• Change final drive oil.
• Change radiator coolant.
• Change power steering oil.
• Change front 4 wheel drive differential oil and axle hub oil.
• Cleaning of fuel tank.

General maintenance points for tractor’s long life and brilliant performance:

• Bleed fuel injector system.
• Check and adjust engine idle RPM (idle RPM should be between recommended RPM only).
• Check and adjust headlight focus.
• Always drive tractor between recommended engine RPM.
• Maintenance tire pressure field and road separately.

Fuse chart of tractor:

This chart is very while troubleshooting any problem related to electrical system.

Troubleshooting:

Here are some basic problem and their possible causes listed below with each one:

• The engine does not start or starts with difficulty.
  • Low fuel level or water in fuel.
  • Air in fuel line.
  • Fuel filter clogged.
  • Fault in fuel injector.
  • Fuel shut off knob is in off position.
• Improper running of engine or misfiring.
  • Quality of diesel is not good.
  • Blockage in fuel line.
  • Fault in fuel injector.
• Engine is not achieving maximum power.
  • Dirty air cleaner bowl and element.
  • Engine overheating.
  • Overload on engine.
  • Incorrect setting of valve clearance.
  • Low temperature for engine operation.
• Abnormal engine knocking.
  • Low engine oil level.
  • Low engine oil pressure.
  • Engine overheating.
• Low temperature for working of engine.
  • Fault in thermostat valve.
  • Incorrect setting valve clearance.
  • Fault in temperature gauge.
• Low engine pressure warning.
  • Level of engine oil is low.
  • Grade of engine oil is not correct.
  • There is any leakage in engine oil.
  • Fault in oil pump.
• Excessive engine oil consumption.
  • Level of engine oil is high.
  • Grade of engine oil is not correct (grade of engine oil should be company recommended).
  • Leakage of engine oil.
• Engine overheating.
  • Fault in radiator cap.
  • Clogged radiator fins.
  • Low level of engine oil.
  • Overloading of engine.
  • Slippage of fan belt.
  • Low level of coolant.
  • Leakage in hoses.
  • Defected thermostat valve.
  • Fault in temperature gauge.
• High fuel consumption.
  • Engine overloading.
  • Air cleaner clogged.
  • Incorrect setting of valve clearance.
  • Implement is not adjusted perfectly.
  • Engine temperature is too low for working.
  • Incorrect water ballasting.
  • Fault in fuel injector nozzles.
  • Tire pressure is not correct.
  • Fault in brake paddles or jammed brake paddles.
• The electrical system is not working.
  • Loose battery terminals.
  • Sulphated battery.
  • Fuse blown.
  • Short circuit.
• Low speed of starter motor.
  • Loose connections.
  • Corrosion in connections.
  • Battery is charged.
• Starter is not working properly.
  • Gear levers are not in neutral position.
  • Loose connections.
  • Battery is totally discharged.
  • Defect in starter motor.
• Alternator light is flashes when engine is running.
  • Loose alternator belt.
  • Engine idle speed is very low.
  • Fault in battery or in alternator.
• Battery is not charging.
  • Corrosion on terminals.
  • Loose terminal connections.
  • Alternator belt loose.
  • Sulphated battery.
  • Fault in battery.
• The hydraulic system is working.
  • Hydraulic filter is clogged.
  • Hydraulic oil level is low.
  • Hydraulic pump is not working.
  • Fault in hydraulic system.
• Hydraulic oil overheating.
  • Level of hydraulic oil is very low.
  • Level of hydraulic oil is high.
  • System is overloaded.
  • Coupling is incorrect.
• Linkage is raising up when lever is operated.
  • Linkage is overloaded.
  • Low pressure setting.
• Linkage does not lift fully upside.
  • Setting of hydraulic lift arm is not correct.
  • Wrong adjustment of internal settings.
• Brake noise.
  • Brake oil contaminated.

Matching implement selection table :-

NOTE:- Gear selections may change with soil condition, weight of implement and transmission type etc.

Instrument cluster features:-

• Engine oil pressure gauge.
• Battery charging indicator.
• Parking brake warning lights.
• Turn indicator.
• Headlight high beam indicator.
• Digital hour meter.
• Engine coolant temperature guage.
• Tachometer.
• Fuel gauge.

Other models :-

New Holland 3630 TX Special Edition specifications

Arjun Novo 655 DI PP CRDI full specifications

Arjun Novo 605 DI PP CRDI full specifications